Veritas Tools
Veritas Tools
 



Veritas Marking Tools


Veritas Woodworking >  Veritas Marking Tools


Veritas Marking & Transfer Tool  (Ref: 101718)

Veritas Marking & Transfer Tool

Key Features

Accurately mark or transfer several positions
Modern interpretation of a traditional story stick
4 reversible marking heads
305mm stainless steel rod and brass foot
Brass foot is reversible for outside or inside measurements/transfers
Made in Canada

The Veritas marking and transfer tool is a very modern interpretation of the traditional story stick. Albeit this is one you can reuse time and time again and is a good deal more accurate than a wooden lathe. The great advantage of this tool is that it lets you accurately mark or transfer several positions at once from a common reference edge. The basic tool includes four 75mm(3") long marking heads, a 305mm(12") stainless steel rod and a brass foot. The marking heads have a single straight reference edge (reversible by flipping the head). The heads will lock at any position along the rod. The brass foot fits on either end of the rod and is reversible for outside or inside measurements. Made in Canada

52.68 63.22


Quantity:  





Veritas Micro-adjust Wheel Marking Gauge

Veritas Micro-adjust Wheel Marking Gauge

Ref: 104388 

30.14 36.17

The micro-adjust wheel marking gauge draws on over 20 years of manufacturing experience, with subtle improvements across the board. The adjustment mechanism built into the stainless-steel rod allows you to set an approximate projection and then fine tune the cutter within a range of just over 6mm.




A fine pitch internal thread allows slow, careful adjustment and locking knobs keep the setting from shifting in use.




The hardened steel wheel cutter scribes perfectly at any point of its circumference, cutting neat marks even in cross grain.


The wheel’s single sided bevel also pulls the gauge face against the stock, helping to maintain accuracy. The cutting edge is at the extreme edge of the rod, allowing you to use the gauge for transferring dimensions such as tenon shoulder and mortice depth.

When not in use the cutter retracts into a countersunk hollow in the gauge face for protection







People who bought this item also bought:
1. Veritas Medium Router Plane (1/2" Blade) (Ref: 717674)
2. Veritas Grinder Tool Rest (Ref: 600320)
3. Veritas Router Plane (Ref: 701927)

Veritas Marking/Mortice Gauge Heads  (Ref: 210949)

Veritas Marking/Mortice Gauge Heads

Key Features
Designed for use with the Veritas Wheel Marking Gauges
Will fit any wheel-marking gauge with a 5/16" dia. Rod
Hardened carbon steel cutters 16mm diameter
Cutters slice wood fibres for clean, accurate lines
Accurate mortice sizing and chisel registration
Shaft collar included ensures prevents accidental tilting in use
Supplied as a pair of cutters with a shaft collar, hex key and instructions
Made in Canada
Description
Though designed for use with the Veritas Wheel Marking Gauges, these mortice gauge heads will convert any wheel-marking gauge (with a 5/16" dia. rod) into a mortice gauge.
Made from hardened carbon steel, the 16mm diameter wheel cutters will scribe at any point in their circumference and slice rather than tear fibres for clean, accurate cuts. The single-bevel cutters can be set as close as 9.5mm apart, with bevels facing each other for accurate mortice sizing and chisel registration. A shaft collar (included) ensures the shaft of the gauge remains parallel to the workpiece, preventing accidental tilting of the cutters in use. Supplied as a pair of cutters with a shaft collar, hex key and instructions. Made in Canada.

8.41 10.09


Quantity:  






3-in-1 Brass Marking Gauge  (Ref: 202397)

3-in-1 Brass Marking Gauge

Key Features
Three tools in one
Cutting gauge, a pin gauge and a wheel gauge
Chuck takes either a pin or a blade
Can be set for either right or left handed use
C/w 12 spare blades, 2 hardened steel pins, a wheel cutter screw, hex key and instruction leaflet
Description
Three tools in one - a cutting gauge, a pin gauge and a wheel gauge. The unique swivelling pin/blade chuck takes either a pin or a blade that locks in place (after extension is set) using a set screw in the end of the 115mm gauge stem. The cutting blade can be set for either right or left handed use. The opposite end of the stem is tapped to accept a 9.5mm diameter wheel cutter. The fence and the internal portion of the locking collet are a single eccentric brass turning. The 25mm diameter fence is eccentric to maximise rub depth. and also prevents the gauge from rolling off the workbench. Comes complete with a dozen spare blades, two hardened steel pins, a wheel cutter screw, hex key and instruction leaflet.

18.50 22.20


Quantity:  


People who bought this item also bought:
1. Veritas Router Plane (Ref: 701927)
2. Veritas Micro-adjust Wheel Marking Gauge (Ref: 104388)





Veritas Saw Guide Clamps (Pr)  (Ref: 952957)

Veritas Saw Guide Clamps (Pr)

50mm capacity clamps
Anodised aluminium with solid brass screws and pads
Fit into T-slot on the underside of the saw guide
Ensure the guide is secure and firmly held in place


These 50mm capacity clamps are anodised aluminium with solid brass screws and pads. They fit into the T-slot on the underside of the saw guide leaving the upper surface clear. These clamps ensure the guide is secure and firmly held in place resulting in a higher degree of accuracy. Made in Canada.

29.28 35.14


Quantity:  


People who bought this item also bought:
1. Veritas Magnetic Saw Guide - 350mm (Ref: 952956)
2. Veritas Dovetail Saddle Marker 1:6 (Ref: 476717)
3. Veritas Saddle Square - Standard (Ref: 202388)


Related products:
1. Veritas Magnetic Saw Guide - 200mm (Ref: 952955)
2. Veritas Magnetic Saw Guide - 350mm (Ref: 952956)





Veritas Magnetic Saw Guide - 350mm  (Ref: 952956)

Veritas Magnetic Saw Guide - 350mm

This anodised aluminium guide helps keep your saw on the right track and perpendicular to a workpiece. It provides a registration surface about 32mm tall. It is particularly useful when crosscutting tenon shoulders or the edges of a dado, which is where you want your saw to cut straight and true. You can hold the guide onto your workpiece with a hand or secure it with clamps. The machined reference surface has three embedded magnets and a covering of UHMW low friction material. The magnets help keep your saw in contact with the guide while the pad allows it to glide along the reference face. The bottom of the guide has two high friction strips to resist slipping on a surface. It also has a T-slot to accept a pair of 50mm capacity clamps (optional accessory). The guide is available in 200 or 350mm lengths. Made in Canada.

24.01 28.81


Quantity:  


People who bought this item also bought:
1. Veritas Saw Guide Clamps (Pr) (Ref: 952957)
2. Veritas Dovetail Saddle Marker 1:6 (Ref: 476717)
3. Veritas Saddle Square - Standard (Ref: 202388)





Veritas Magnetic Saw Guide - 200mm  (Ref: 952955)

Veritas Magnetic Saw Guide - 200mm

Key Features
Anodised aluminium guide keeps your saw on the right track
Useful when crosscutting tenon shoulders or dadoes
32mm tall, machined reference surface with three embedded magnets
UHMW low friction cover allows saw to glide effortlessly

Made in Canada

This anodised aluminium guide helps keep your saw on the right track and perpendicular to a workpiece. It provides a registration surface about 32mm tall. It is particularly useful when crosscutting tenon shoulders or the edges of a dado, which is where you want your saw to cut straight and true. You can hold the guide onto your workpiece with a hand or secure it with clamps. The machined reference surface has three embedded magnets and a covering of UHMW low friction material. The magnets help keep your saw in contact with the guide while the pad allows it to glide along the reference face. The bottom of the guide has two high friction strips to resist slipping on a surface. It also has a T-slot to accept a pair of 50mm capacity clamps (optional accessory). The guide is available in 200 or 350mm lengths. Made in Canada.

22.18 26.62


Quantity:  






Veritas Dual Marking Gauge  (Ref: 952906)

Veritas Dual Marking Gauge

With two independently adjustable rods, this gauge can scribe both sides of a mortice at once. The length of each ground stainless-steel rod is very precise. By registering the tails against either side of a chisel, you can set the cutters to span the exact width of the chisel blade. Projection is easy to set, an internal O-ring keeps light but constant friction on each rod; a thumbscrew locks the setting. One rod has its cutting edge at the extreme end of the rod, making it useful for transferring dimensions or as a depth gauge. As with all Veritas marking gauges, the wheel cutters avoid the problems of wandering that can occur with pin-style marking gauges. They cut wood fibres rather than tear them and they mark cleanly, even on cross grain. These hardened steel wheel cutters scribe perfectly at any point of their circumference. They are oriented with the cutting bevels facing in opposite directions, so you can always mark your line with the bevel facing the waste side of any cut. Each cutter is fully retractable for safe storage or to permit use with a single cutter.

The rods project off-centre from the anodized aluminium body, which helps the gauge resist rolling on a workbench and maximizes the area of the 50mm diameter brass face that can register against the work piece. 190mm overall, the gauge has a setting range from zero to 145mm. The aluminium housing has a brass face and the rods are stainless steel.

33.94 40.73


Quantity:  






Veritas Shaft Clamp for Dual Marking Gauge  (Ref: 952932)

Veritas Shaft Clamp for Dual Marking Gauge

Key Features

Hardened steel wheel cutters
Cuts wood fibres, rather than tears
Marks cleanly, even on cross grain
Wheels retract into the head of the gauge for storage and protection
The gauges are very easy to set
Made in Canada

On occasions, it may be an advantage to lock the relative position of the two rods on the Veritas® Dual Marking Gauge, such as when a project requires a constant mortice size, but different offsets. The shaft clamp lets you lock the relative position of the cutters while still being able to adjust the fence for offset. This allows you to preserve identical mortice or tenon sizing when joining parts of different thicknesses or when adding a reveal, since it prevents the cutter settings from shifting while the fence is being repositioned. Machined to precise tolerances to prevent binding on the rods, the 13mm long collar is made from extruded aluminium, with a turned brass thumbscrew that tightens onto the marking gauge’s steel guide rods without marring their surfaces. Made in Canada.

5.30 6.36


Quantity:  






Veritas Dual Marking Gauge & Shaft Clamp Package  (Ref: 717714)

Veritas Dual Marking Gauge & Shaft Clamp Package



COMPRISES

952906 Veritas Dual Marking Gauge

Key Features

Hardened steel wheel cutters
Cuts wood fibres, rather than tears
Marks cleanly, even on cross grain
Wheels retract into the head of the gauge for storage and protection
The gauges are very easy to set
Made in Canada

AND

952932 Veritas Shaft Clamp for Dual Marking Gauge

37.37 44.84


Quantity:  






Veritas Precision Square - Metric  (Ref: 952847)

Veritas Precision Square - Metric

26.74 32.09


Quantity:  






Veritas Trammel Points  (Ref: 102159)

Veritas Trammel Points

Key Features

Stainless steel for durability and corrosion resistance
Points score clear lines on wood, aluminium, brass, bronze and mild steel
Removable tips, trammel bodies double as square gauges
Trammels fit onto any rule or straight edge up to 6.35mm(1/4") thick
Each trammel is 12.7mm(1/2") and 63.5mm(2.1/2") long overall
Made in Canada

Inspired by an antique trammel set found at a woodworking show, the Veritas version is made of stainless steel for durability and corrosion resistance. The removable points score clear lines on any wood and are also effective on aluminium, brass, bronze and mild steel. Knurled sections make the tips easier to remove. With the points removed, the trammel bodies double as square gauges, clamping onto a square to make repetitive angle marking easy. The trammels will fit onto any rule or straight edge up to 6.35mm(1/4") thick. Being narrow bodied they can scribe a circle with as small a radius as 14.5mm(9/16"). Each trammel is 12.7mm(1/2") and 63.5mm(2.1/2") long overall. Made in Canada

17.96 21.55


Quantity:  






Veritas Carpenter's Gauge - 300mm (12")  (Ref: 475905)

Veritas Carpenter's Gauge - 300mm (12

Designed to be carried in an apron/pocket
Locks vertically for usage, locks horizontally for easy storage/carry
Direct reading in metric/imperial
Scribe circles up to 300mm (12")
Made of brass, stainless steel and tough ABS


Made to fit easily into the pocket, the carpenter's gauge combines both direct reading compass and marking gauge in one tool. It will precisely draw circles up to 300mm(12") in diameter and can easily be used to find the centre for a corner radius and then quickly reversed to accurately draw the corner radius. The stainless steel rule is graduated with both imperial and metric scales. Fast, efficient and accurate, the Veritas Carpenter's Gauge will find a welcome home in many apron pockets, tool bags and cabinetmaker's tool chests.

16.09 19.31


Quantity:  






Veritas Beam Compass  (Ref: 474583)

Veritas Beam Compass

There are some circle layout jobs that ordinary compasses just aren't suitable for, a beam compass (or trammel) is much more practical especially when drawing large diameter accurately. Using a single beam section, the Veritas® beam compass deals with circles from 38mm(1.1/2") to 610mm(24") in diameter. Additional sections take you up to 2,030mm(80") for circular tables, rockers, arches, etc. It has carbide-tipped points that readily scribe metal as well as wood, although the pencil head is usually used for marking out on wood. A micro-adjust feature quickly gives accurate settings. All of this comes in a fitted wooden case that even includes a small brass centre pivot disc for use where it is important not to mar work. The beams are steel and the fittings are all solid brass.

91.06 109.27


Quantity:  






Veritas Transfer Log Scribe  (Ref: 202391)

Veritas Transfer Log Scribe

Aluminium alloy with brass fittings
Supplied with double ended steel guide pin
Use for compass work and transfer scribing
Fully adjustable from 0-300mm
Bi-directional level bubbles ensure accuracy
Supplied with an indelible pencil


Made from aluminium alloy with brass fittings, the Transfer Scribe comes with a double ended steel guide pin. The pin has a pointed end for compass work and a rounded curved end for smooth scribing. The pin can be replaced with a pencil for double scribing. Fully adjustable from 0-300mm. Bi-directional level bubbles help guide the user and ensure the scribe is as accurate as possible. Any standard pencil can be used, the Transfer is supplied with an indelible pencil that marks well with only light pressure.

80.85 97.02


Quantity:  






Veritas Beam Compass Heads  (Ref: 610137)

Veritas Beam Compass Heads

Aluminum heads clamp on bar from 5/8"- 3/4"
Unlimited circle size
Brass clamping knob tightly holds to beam
Points have 1/8" of fine adjustment
Hardened points mark surfaces such as steel plate
Includes pencil for marking wood & wallboard


Made to the usual Veritas high quality standard, these beam compass (or trammel) heads can be clamped to any length of material between 5/8" (16mm) and 3/4" (19mm) thick to produce accurate circles or arcs of any size. Two examples of the attention to detail typical of the manufacturer are the pointed steel pins which are positioned adjacent to the clamping screws to ensure a secure grip and the offset point on one of the pins which allows for fine setting of the radius. Materials used are hardened steel, brass and anodised aluminium and there is a plastic storage case provided.

38.88 46.66


Quantity:  






Veritas Micro-Adjust Gauge - Non-Graduated  (Ref: 475315)

Veritas Micro-Adjust Gauge - Non-Graduated

Hardened steel wheel cutter
Cuts wood fibres, rather than tears
Marks cleanly, even on cross grain
The wheel retracts into the face of the gauge for storage and protection
The gauges are very easy to set
Use as a depth gauge to transfer measurements


There are two main problems with a typical marking gauge: you have to tilt it just right to avoid pin chatter and, even then, the pin tends to follow the wood grain, throwing off your line. The Veritas wheel marking gauges solve both problems. The hardened steel wheel cutter scribes perfectly at any point of its circumference. Since it cuts wood fibres rather than tears, it marks cleanly, even on cross grain. The wheel's singlesided bevel also pulls the gauge face against the stock, maintaining accuracy.

Its cutting edge is at the extreme end of the rod, useful for transferring dimensions such as tenon shoulder and mortise depth. The wheel retracts into the face of the gauge for storage and protection. The gauges are very easy to set, since each has an internal O-ring to keep light but constant friction on the rod.

The Veritas standard marking gauge is a great workhorse and excellent value. Due to the number of requests for a micro-adjust feature, Veritas offer a second model with a slightly longer body fitted with a two-stage collet to allow fine adjustment of the cutting wheel. The collet has a fine-pitch thread; one revolution advances or retracts the wheel 0.8mm. The knurled thumbscrew then locks the setting. The rod of the Imperial gauge is graduated to 6" in 16ths; the metric version has graduations to 150mm. Very comfortable gauges to use.

22.99 27.59


Quantity:  





Veritas Standard Wheel Gauge - Non-Graduated

(Ref: 475382)
20.05 24.06
 
Quantity:  


Veritas Micro-Adjust Gauge - Metric Graduations

(Ref: 210530)
25.07 30.08
 
Quantity:  


Veritas Micro-Adjust Gauge - Imperial Graduations

(Ref: 475131)
25.07 30.08
 
Quantity:  


Veritas Replacement Wheel for Gauges

(Ref: 477717)
2.82 3.38
 
Quantity:  



Veritas Saddle Square - Standard  (Ref: 202388)

Veritas Saddle Square - Standard

Allow the scribing of two perpendicular surfaces at one time
Made of anodized aluminium
Version is available for stud wall layout


Transferring a line from face side to face edge and vica versa of timber is now as easy as falling off a log. With this saddle square the line can be marked in both planes without moving the square and maintaining prime accuracy without really trying. Produced in anodised aluminium to a practical but stylish design, which is available in two sizes. One at 50mm wide, the standard, forms an "L", of 32 x 57mm, the large version 34 x 84mm and 38mm wide has a central slot for locating and marking stud locations accurately.

9.10 10.92


Quantity:  


People who bought this item also bought:
1. Veritas Saw Guide Clamps (Pr) (Ref: 952957)
2. Veritas Magnetic Saw Guide - 350mm (Ref: 952956)
3. Veritas Dovetail Saddle Marker 1:6 (Ref: 476717)





Veritas Saddle Square - Large  (Ref: 202389)

Veritas Saddle Square - Large

The large version of the Veritas Saddle Square is 34 x 84mm and 38mm wide has a central slot for locating and marking stud locations accurately.

Transferring a line from face side of timber to face edge and vice versa is now as easy as falling off a log. With this saddle square the line can be marked in both planes without moving the square hence maintaining prime accuracy without really trying. Produced in anodised aluminium to a practical but stylish design, and available in two sizes. One at 50mm wide, (the standard), forms an "L", of 32 x 57mm, the large version 34 x 84mm and 38mm wide has a central slot for locating and marking stud locations accurately.

10.95 13.14


Quantity:  






Veritas Mitre Saddle  (Ref: 202386)

Veritas Mitre Saddle

Transferring a 45° mitre line to an adjacent perpendicular face is never easy, judging the exact position can be tricky. Not so, if it can be done with a single tool such as this Veritas Mitre Saddle. Smaller stock is also much easier to mark using this tool. The square leg is 55mm long, and the mitre face 45mm long by 32mm deep. Made from anodised aluminium.

9.72 11.66


Quantity:  


People who bought this item also bought:
1. Veritas Saw Guide Clamps (Pr) (Ref: 952957)
2. Veritas Magnetic Saw Guide - 350mm (Ref: 952956)
3. Veritas Dovetail Saddle Marker 1:6 (Ref: 476717)





Veritas Centre Finder  (Ref: 610133)

Veritas Centre Finder

Mark timber up to 6"across
Knife edge steelblade
Pre-drilled for mounting
Made from die-cast aluminium
Requires no effort
Works on square/cylinder stock
Good on other surfaces too
Accurate to 1/12"


A simple and accurate tool for finding the centre of a piece of timber. Made from aluminium and pre-drilled for mounting conveniently near the lathe, it uses a knife-edged steel blade to score the end of the workpiece. Simply place a square or cylinder (up to 6" across) in the centre finder, tap it with a mallet, turn the wood 90° and tap it again. The result is two score lines which mark the centre of the workpiece. The Veritas Centre Finder functions well even with work that is not square. Just score the end of your workpiece four times rather than twice. This will give you a small polygon and you can then dot the centre of it by eye. It particularly shines when work has to be replaced on the lathe after waste ends have been removed. Because it is so accurate, you can re-establish the exact centre of any cylinder.

15.40 18.48


Quantity:  






Veritas Workshop Striking Knife  (Ref: 504089)

Veritas Workshop Striking Knife

Key Features

A2 tool-steel blade, ground to a point
Leaves a clearly incised line, improves accuracy
0.8mm thick and 8mm wide by 38mm long blade
Useful for the precise transfer of dovetail layouts
Dual bevel suitable for right or left-hand use
Nylon-reinforced ABS handle comfortable, controlled grip
Supplied with a guard to protect the tip in storage
170mm long overall
Made in Canada

The knife has an A2 tool-steel blade, ground to a point with a 25° bevel. It leaves a clearly incised line that serves to guide a saw or chisel when starting a cut, helping to improve accuracy. At 0.8mm thick and 8mm wide, the blade projects about 38mm from the handle. It is particularly useful for the precise transfer, as for dovetail layouts. The dual bevel means it is equally suitable for right or left-hand use. The contoured, nylon-reinforced ABS handle makes for a comfortable, controlled grip. Flats on the sides prevent the knife from rolling on a surface. Supplied with a guard to protect the tip in storage. 170mm long overall. Made in Canada

12.95 15.54


Quantity:  






Veritas Woodworking >  Veritas Marking Tools



Veritas Marking Tools
Buy online at www.quality-woodworking-tools.com with FREE mainland UK delivery for all woodworking tools





Veritas Tools Homepage
Veritas Checkout
  View Basket
Veritas Tools UK Delivery
Free UK Delivery

Newsletter Subscription