Veritas Tools
Veritas Tools
 



Veritas Saws


Veritas Woodworking >  Veritas Saws


Veritas Tenon Saw Rip Cut 9tpi  (Ref: 506361)

Veritas Tenon Saw Rip Cut 9tpi

Key Features

Choose from rip cut 9tpi or crosscut 12tpi
High-carbon steel blades 400mm long
Brass nut secures comfortable Bubinga handle
Excellent feel and balance

The unique designs of the Veritas carcass saws and dovetail saws have proved to be extremely popular and Veritas have now introduced two superb 400mm tenon saws to complement their range. They combine the best characteristics of this fine classic joinery saw with those of state-of-the-art materials and construction methods. The tooth pattern on the thin high-carbon steel blades provide a good balance between cutting action and surface finish. The design of the Bubinga wooden handle has been developed to give good power transfer while still allowing a three or four finger grip for precise control. Available in crosscut and rip cut versions, the crosscut being excellent for trimming parts to length or for use with a mitre box. The rip saw is optimised for the fast accurate cutting of tenon cheeks and similar cutting operations with the grain.The crosscut saw has 12tpi with a 15° rake and an included angle of 60°, set is 0.06720mm per side. The teeth are filed at an alternating 75° angle to the blade, which creates a 15° bevel on each tooth.The rip saw has 9tpi with a 14° rake using the typical 60° included angle, set is the same as on the crosscut saw.To fully appreciate the beauty, handling and performance of these saws, we are afraid you are just going to have to treat yourself

84.56 101.47


Quantity:  






Veritas Tenon Saw Crosscut 12 TPI  (Ref: 506362)

Veritas Tenon Saw Crosscut 12 TPI

Key Features

Choose from rip cut 9tpi or crosscut 12tpi
High-carbon steel blades 400mm long
Brass nut secures comfortable Bubinga handle
Excellent feel and balance

The unique designs of the Veritas carcass saws and dovetail saws have proved to be extremely popular and Veritas have now introduced two superb 400mm tenon saws to complement their range. They combine the best characteristics of this fine classic joinery saw with those of state-of-the-art materials and construction methods. The tooth pattern on the thin high-carbon steel blades provide a good balance between cutting action and surface finish. The design of the Bubinga wooden handle has been developed to give good power transfer while still allowing a three or four finger grip for precise control. Available in crosscut and rip cut versions, the crosscut being excellent for trimming parts to length or for use with a mitre box. The rip saw is optimised for the fast accurate cutting of tenon cheeks and similar cutting operations with the grain.The crosscut saw has 12tpi with a 15° rake and an included angle of 60°, set is 0.06720mm per side. The teeth are filed at an alternating 75° angle to the blade, which creates a 15° bevel on each tooth.The rip saw has 9tpi with a 14° rake using the typical 60° included angle, set is the same as on the crosscut saw.To fully appreciate the beauty, handling and performance of these saws, we are afraid you are just going to have to treat yourself

84.56 101.47


Quantity:  






Veritas Gents Saw - Rip Cut  (Ref: 952907)

Veritas Gents Saw - Rip Cut

0.4mm thick high-carbon steel
Injection moulded back creates a solid one-piece blade/spine/mount assembly
Brass nut secures comfortable Bubinga handle
Saw cuts easily and stays true


Sharing the same, advanced materials as the Veritas dovetail and carcass saws, these Gent’s saws have 200mm long high-carbon steel blades just 0.4mm thick with 0.08mm of teeth set per side. The 20tpi ripsaw has teeth with a 14" rake angle and a 60° included angle. The teeth on the 22tpi crosscut saw have a rake angle of 15°, an included angle of 60° and alternating 15° bevel angles so that they sever rather than tear wood fibres. Both saws have a cut depth of 41mm. For strength and rigidity, the glass and stainless steel-filled polymer spine is moulded over the blade and handle stud. A brass nut secures the Bubinga handle to the blade. Made in Canada.

39.25 47.10


Quantity:  






Veritas Gents Saw - Cross Cut  (Ref: 952908)

Veritas Gents Saw - Cross Cut

39.25 47.10


Quantity:  






Veritas Rip Cut Carcass Saw  (Ref: 950979)

Veritas Rip Cut Carcass Saw

The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed for rip cutting at 12tpi. The teeth have a rake angle of 10°, an included angle of 60° for fast and accurate cutting along the line of the grain. The depth of cut is 60mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the grip makes for a comfortable and secure grip. Overall length 415mm (16.1/4")

49.95 59.94


Quantity:  






Veritas Crosscut Carcass Saw  (Ref: 950978)

Veritas Crosscut Carcass Saw

The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed crosscut at 14tpi. The teeth have a rake angle of 15°, an included angle of 60° with alternate 15° bevels to efficienlty sever wood fibres rather than tear. The depth of cut is 60mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the grip makes for a comfortable and secure grip. Overall length 415mm (16.1/4").

49.95 59.94


Quantity:  






Veritas Fine-Tooth Dovetail Saw-05T05.05  (Ref: 211804)

Veritas Fine-Tooth Dovetail Saw-05T05.05

For woodworkers who prefer a fine-tooth dovetail saw, Veritas produce a premium example with a 20 teeth per 25mm (20tpi blade) filed for rip cutting. It has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade. The teeth have a rake angle of 14°, and an included angle of 60°. The depth of cut is about 40mm (1.9/16").The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

47.12 56.54


Quantity:  






Veritas Small Crosscut Saw  (Ref: 211803)

Veritas Small Crosscut Saw

The saw has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade filed with 16 teeth per 25mm (16tpi). The teeth have 15° rake and bevel angles. The depth of cut is about 40mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

47.12 56.54


Quantity:  






Veritas Dovetail Saw 230mm x 14tpi  (Ref: 210923)

Veritas Dovetail Saw 230mm x 14tpi

The saw's spine is permanently moulded onto the back of the blade. It imparts just the right amount of weight to the blade to carry the saw effortlessly into the cut. The polished hardwood handle is shaped to fit the hand comfortably and not just to look pretty, which it also does. In fact the handle is very reminiscent of the rear tote on a bench plane and this theme is carried on in the steel rod and brass nut used to attach the handle onto the spine. A mortice and tenon joint between handle and back ensures a good solid and secure fixing between the two parts. The blade is Japanese high carbon steel, 230mm (9") long by 40mm (1.1/2") deep, with razor sharp 14tpi teeth filed with a 14° rake angle, the overall weight is 360g (12.7oz).

47.12 56.54


Quantity:  






Veritas Flush-Cutting Saw - Double Edge  (Ref: 475855)

Veritas Flush-Cutting Saw - Double Edge

A double edged style that cuts from either side. Each is about 290mm long with 120mm of blade.

15.63 18.76


Quantity:  






Veritas Detail Flush-Cutting Saw - Single Edge 26tpi  (Ref: 504598)

Veritas Detail Flush-Cutting Saw - Single Edge 26tpi


Key Features

Used to cut off a projection
Teeth set one way, no damage to surface
Japanese style toothed blade
Blade can be pressed flush
Rigid enough to corner
Overall length 290mm(11.1/2") with 120mm(4.3/4") blade
Made in Canada

14.09 16.91


Quantity:  






Veritas Jointer & Edger  (Ref: 600304)

Veritas Jointer & Edger

Dual purpose
Topping off teeth prior to re-sharpening
Provides an accurate guide for filing edges of cabinet scrapers
45° guide face for sharpening scraper and plane blades


Serving the dual purposes of topping off the teeth of a hand saw prior to re-sharpening, and providing an accurate guide for filing the edges of cabinet scrapers. A file with a maximum thickness of 4.7mm, typically a 150mm second cut hand file, is clamped into the guide and run across the saw teeth or the scraper to produce an even and square result. The 45° guide face enables other scraper blades to be sharpened. Another use for this versatile tool is for keeping your ski edges nice and sharp; how versatile can you get?

11.16 13.39


Quantity:  






Veritas Right-Angle Saw Guide- T0401  (Ref: 202387)

Veritas Right-Angle Saw Guide- T0401

Manufactured using precision machined aluminium extrusion with brass fittings. The reference surface is embedded with a 19mm rare earth magnet and covered with a low friction UHMW pad. The magnets keep the saw aligned; the pads allow the saw to slide easily against the reference surface. The clamp can accommodate material from 6mm to 25mm thick. The guide can be used with virtually any backless saw, however the Veritas dovetail saw is specifically designed for the job; with a 50 x 215mm, 22tpi blade, effective in both cross and rip cuts.

28.87 34.64


Quantity:  


People who bought this item also bought:
1. Veritas Magnetic Saw Guide - 350mm (Ref: 952956)





Veritas Saw Depth Stop  (Ref: 102519)

Veritas Saw Depth Stop

Key Features

Effective way to control the depth of cut
Simple to set up, fits virtually any tenon saw
230mm (9") long aluminium rail with magnetic strip
60mm (2-3/8") range of adjustment
Brass knobs to lock the rail at the desired cut depth

The Veritas saw depth stop is an effective and simple way to control the depth of cut when using a tenon saw. It consists of a 230mm (9") long aluminium rail, which has a high friction magnetic strip. This holds the strip onto the saw blade. Attached to the strip are two stainless steel rods that give the rail a 60mm (2-3/8") range of adjustment. The two clamp knobs, with rare-earth magnet bases, register against the spine of the saw. All you need do is simply tighten the brass knobs to lock the rail at the desired cut depth, foolproof.

21.82 26.18


Quantity:  






Veritas Dovetail Saw T0203  (Ref: 202379)

Veritas Dovetail Saw T0203

15.87 19.04


Quantity:  






VERITAS SMALL CROSSCUT SAW & FINE TOOTH DOVETAIL SAW 211803 / 211804  (Ref: 717451)

VERITAS SMALL CROSSCUT SAW & FINE TOOTH DOVETAIL SAW 211803 / 211804

SPECIAL OFFER VERITAS SMALL CROSSCUT SAW & FINE TOOTH DOVETAIL SAW 211803 / 211804

Veritas Small Crosscut Saw

The saw has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade filed with 16 teeth per 25mm (16tpi). The teeth have 15° rake and bevel angles. The depth of cut is about 40mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")



Veritas Fine-Tooth Dovetail Saw



For woodworkers who prefer a fine-tooth dovetail saw, Veritas produce a premium example with a 20 teeth per 25mm (20tpi blade) filed for rip cutting. It has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade. The teeth have a rake angle of 14°, and an included angle of 60°. The depth of cut is about 40mm (1.9/16").The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

87.40 104.88


Quantity:  






VERITAS DOVETAIL SAW & FINE TOOTH SAW 210923 / 211804  (Ref: 717452)

VERITAS DOVETAIL SAW & FINE TOOTH SAW 210923 / 211804

SPECIAL OFFER VERITAS DOVETAIL SAW & FINE TOOTH SAW 210923 / 211804 PACKAGE

Veritas Dovetail Saw 230mm x 14tpi

The saw's spine is permanently moulded onto the back of the blade. It imparts just the right amount of weight to the blade to carry the saw effortlessly into the cut. The polished hardwood handle is shaped to fit the hand comfortably and not just to look pretty, which it also does. In fact the handle is very reminiscent of the rear tote on a bench plane and this theme is carried on in the steel rod and brass nut used to attach the handle onto the spine. A mortice and tenon joint between handle and back ensures a good solid and secure fixing between the two parts. The blade is Japanese high carbon steel, 230mm (9") long by 40mm (1.1/2") deep, with razor sharp 14tpi teeth filed with a 14° rake angle, the overall weight is 360g (12.7oz).

Veritas Fine-Tooth Dovetail Saw

For woodworkers who prefer a fine-tooth dovetail saw, Veritas produce a premium example with a 20 teeth per 25mm (20tpi blade) filed for rip cutting. It has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade. The teeth have a rake angle of 14°, and an included angle of 60°. The depth of cut is about 40mm (1.9/16").The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

87.40 104.88


Quantity:  






Veritas 10mm Tapered Snug Plug Cutter & Flush Cutting Saw Package  (Ref: 717718)

Veritas 10mm Tapered Snug Plug Cutter & Flush Cutting Saw Package



510265 Veritas Tapered Plug Cutter - 10mm

Snug plug cutters cut a slightly tapered plug
Flares out at 3° angle
Four cutting flutes


Sometimes when plugging holes, no matter how carefully drilled, the holes finish up slightly oversize for the plug, especially in soft woods. These cabinet maker's snug plug cutters overcome this by cutting a slightly tapered plug. The first 3mm of the plug is the diameter stated whilst the remaining length is then flared out at an angle of 3°. Just tap the plug into place until you meet resistance then cut off the excess. Also, unlike regular plug cutters which have two cutting flutes, these plug cutters have four, giving a much cleaner cut and a smooth-sided plug which fits perfectly every time and is practically invisible. For best results use in a drill press or power drill stand.


PLUS

504598 Veritas flush Cutting Saw

Key Features

Excellent for cutting projecting dowels or plugs
Double edged 22tpi with teeth set one way
Single edged 26tpi with no set
Japanese style tooth pattern
Flexible blades cut on the pull stroke
Overall length 290mm(11.1/2") with 120mm(4.3/4") blade
Made in Canada



27.90 33.48


Quantity:  






VERITAS DOVETAIL SAW & FINE TOOTH SAW & CROSSCUT SAW2 10923 / 211804 / 211803  (Ref: 717453)

VERITAS DOVETAIL SAW & FINE TOOTH SAW & CROSSCUT SAW2 10923 / 211804 / 211803

SPECIAL OFFER VERITAS DOVETAIL SAW & FINE TOOTH SAW & CROSSCUT SAW210923 / 211804 / 211803 TRIPLE PACKAGE

Veritas Dovetail Saw 230mm x 14tpi

The saw's spine is permanently moulded onto the back of the blade. It imparts just the right amount of weight to the blade to carry the saw effortlessly into the cut. The polished hardwood handle is shaped to fit the hand comfortably and not just to look pretty, which it also does. In fact the handle is very reminiscent of the rear tote on a bench plane and this theme is carried on in the steel rod and brass nut used to attach the handle onto the spine. A mortice and tenon joint between handle and back ensures a good solid and secure fixing between the two parts. The blade is Japanese high carbon steel, 230mm (9") long by 40mm (1.1/2") deep, with razor sharp 14tpi teeth filed with a 14° rake angle, the overall weight is 360g (12.7oz).

Veritas Fine-Tooth Dovetail Saw

For woodworkers who prefer a fine-tooth dovetail saw, Veritas produce a premium example with a 20 teeth per 25mm (20tpi blade) filed for rip cutting. It has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade. The teeth have a rake angle of 14°, and an included angle of 60°. The depth of cut is about 40mm (1.9/16").The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

Veritas Small Crosscut Saw

The saw's spine is permanently moulded onto the back of the blade. It imparts just the right amount of weight to the blade to carry the saw effortlessly into the cut. The polished hardwood handle is shaped to fit the hand comfortably and not just to look pretty, which it also does. In fact the handle is very reminiscent of the rear tote on a bench plane and this theme is carried on in the steel rod and brass nut used to attach the handle onto the spine. A mortice and tenon joint between handle and back ensures a good solid and secure fixing between the two parts. The blade is Japanese high carbon steel, 230mm (9") long by 40mm (1.1/2") deep, with razor sharp 14tpi teeth filed with a 14° rake angle, the overall weight is 360g (12.7oz).

131.10 157.32


Quantity:  






Veritas Tapered Snug Plug Cutter & Flush Cutting Saw - PACKAGE DEAL  (Ref: 717578)

Veritas Tapered Snug Plug Cutter & Flush Cutting Saw - PACKAGE DEAL

Key Features

Veritas Tapered Snug Plug Cutter

Snug plug cutters cut a slightly tapered plug
1/2" Cutter
Flares out at 3° angle
Four cutting flutes
Veritas Flush Cutting Saws

Excellent for cutting projecting dowels or plugs
Single edged 26tpi with no set
Japanese style tooth pattern
Flexible blades cut on the pull stroke
Overall length 290mm(11.1/2") with 120mm(4.3/4") blade

Package deal comprises the Veritas 1/2" Tapered Snug Plug Cutter and the Veritas Flush Cutting Saw.

Veritas 1/2" Tapered Snug Plug CutterSometimes when plugging holes, no matter how carefully drilled, the holes finish up slightly oversize for the plug, especially in soft woods. These cabinet maker's snug plug cutters overcome this by cutting a slightly tapered plug. The first 3mm of the plug is the diameter stated whilst the remaining length is then flared out at an angle of 3°. Just tap the plug into place until you meet resistance then cut off the excess. Also, unlike regular plug cutters which have two cutting flutes, these plug cutters have four, giving a much cleaner cut and a smooth-sided plug which fits perfectly every time and is practically invisible. For best results use in a drill press or power drill stand.

Veritas Flush Cutting SawTraditionally used for the rapid trimming of plugs and dowels flush with a surface, these flush cutting saws can be used where you want to cut off a projection without damaging the surrounding or adjoining face. The Japanese tooth pattern blade cuts aggressively (on the pull stroke), but does not mark the surface that it is cutting next to. The thin blade is flexible and can be pressed flush to any surface, yet is rigid enough for good control. 290mm long with 120mm of blade. Single edge 26tpi. These work like a charm.

27.10 32.52


Quantity:  






Veritas Woodworking >  Veritas Saws



Veritas Saws
Buy online at www.quality-woodworking-tools.com with FREE mainland UK delivery for all woodworking tools





Veritas Tools Homepage
Veritas Checkout
  View Basket
Veritas Tools UK Delivery
Free UK Delivery

Newsletter Subscription