Veritas Tools
Veritas Tools
 



Veritas Workbench Accessories


Veritas Woodworking >  Veritas Workbench Accessories


Veritas Bench Blade - Standard Post  (Ref: 212617)

Veritas Bench Blade - Standard Post

So named because of their very low profile, they project only 6mm, above your bench top. A thumb-operated eccentric cam lever controls the sliding jaw, allowing you to secure work quickly. The jaw has a 6mm range of travel and applying up to 130kg of force. Flats on the cam provide secure stops at 3mm and 6mm of travel. The jaw face has a 5° inward cant to help hold a work piece securely. The cam and jaw are cast steel, heat-treated for surface hardness. The standard post version is for use in a 19mm (3/4") diameter through-hole (or blind holes at least 47mm deep).

11.89 14.27


Quantity:  






Veritas Bench Blade - Wedge-Lock Post  (Ref: 212618)

Veritas Bench Blade - Wedge-Lock Post

The wedge-lock version is usable at any angle from horizontal to vertical. It will anchor firmly in a 19mm (3/4") diameter through-hole in material as thin as 16mm or in blind holes that are a minimum of 34mm deep.

17.96 21.55


Quantity:  






Veritas Hold Down Clamp  (Ref: 500229)

Veritas Hold Down Clamp

Exceptionally high clamping forces
Arm pivots independently
Levered forces exerted downward
Fine grooves on post resist upward forces
200mm of clamping and throat capacity

Exceptionally high clamping forces can be obtained with this hold down. The arm is free to pivot independently, all levered forces are exerted downward, without any loss due to horizontal slippage from the canting action of the hold down post. The fine grooves on the post resist upward forces, yet still allow easy entry into a 19mm diameter hole. The 250mm hold down post gives you 200mm of clamping capacity, matching the 200mm throat capacity. Used vertically on the top of a bench, or horizontally in a side skirt.

67.78 81.34


Quantity:  






Veritas Pair Bench Dogs  (Ref: 475715)

Veritas Pair Bench Dogs

Made from solid brass rod so are non-corroding
Combined crosshatching and 2° slope face hold wood securely
Side spring slides cleanly and holds it well
Bench dog 110mm (fit 19mm hole)
For benches with tops up to 50mm thick
Ideal for use in bench sides
Works well with Wonder Dog Clamps

18.50 22.20


Quantity:  






Vertitas Pair Bench Pups  (Ref: 475881)

Vertitas Pair Bench Pups

Made from solid brass rod - non-corroding
Combined crosshatching and 2° slope face hold wood securely
Side spring slides cleanly and holds it well
Bench Pups at 60mm (fit 19mm hole)
For benches with tops up to 50mm thick
Ideal for use in bench sides
Works well with Wonder Pup Clamps

15.19 18.23


Quantity:  






Veritas Bench Anchor  (Ref: 210539)

Veritas Bench Anchor

It is easiest to think of this as a barrel-shaped insert nut that secures in any 19mm(3/4") diameter hole, except this one self-anchors and is removable. Usable horizontally, vertically or at any angle in between, it accepts common 1/2" UNC threaded bolts, and will wedge in through-holes in material as thin as 16mm(5/8") or in blind holes 32mm deep. With pull-out strength of at least 90kgs in hardwood, the anchor has a wedging mechanism controlled by an integral hex-head screw drive and an external rubber O-ring that uses friction to hold it in place during installation. Though any 1/2" UNC threaded rod or bolt may be used with our bench anchor, we offer a small selection of flat-head and round-head fasteners here for convenience. The 27mm diameter washer, for use with round-head fasteners, increases the surface contact area of the head, made in Canada.

8.70 10.44


Quantity:  






Veritas Wonder Dog  (Ref: 202392)

Veritas Wonder Dog

Hugely versatile bench top fittings, which come in very handy for all sorts of jig and homemade clamping devices. Veritas Wonder Dogs are basically bench dogs with a length of threaded bar through the top, tommy bar one end and brass clamping face at the other. Dogs are 165mm. Dogs have a spring retainer. Above 38mm use Dogs. All that is required to mount them is a 19mm hole. Use for making: Long Clamps, Curved Work, Jigs, Unique Shapes, Bench Work.

23.89 28.67


Quantity:  






Veritas Wonder Pup  (Ref: 202393)

Veritas Wonder Pup

Hugely versatile bench top fittings, which come in very handy for all sorts of jig and homemade clamping devices. Veritas Wonder Pups are basically bench dogs with a length of threaded bar through the top, tommy bar one end and brass clamping face at the other. Pups are 70mm. Pups have an O-ring. Below 38mm use Pups. All that is required to mount them is a 19mm hole. Use for making: Long Clamps, Curved Work, Jigs, Unique Shapes, Bench Work.

21.77 26.12


Quantity:  






Veritas Stainless Steel Bench Dogs (Pair)  (Ref: 504542)

Veritas Stainless Steel Bench Dogs (Pair)

Key Features

Stainless steel dogs for use with Festool MFT3 table
Designed by Peter Parfitt, manufactured by Veritas®
Very useful accessory for making accurate, repeatable cuts
Can be used with any guide rail and saw
Excellent for attaching jigs and accessories

9.23 11.08


Quantity:  






Veritas Stainless Steel Parf Dogs (Pair)  (Ref: 504543)

Veritas Stainless Steel Parf Dogs (Pair)

Key Features

Stainless steel dogs for use with Festool MFT3 table
Designed by Peter Parfitt, manufactured by Veritas®
Very useful accessory for making accurate, repeatable cuts
Can be used with any guide rail and saw
Excellent for attaching jigs and accessories

Manufactured by Veritas®, Parf dogs were designed by Peter Parfitt, an online reviewer and regular contributor to woodworking magazines. Parf dogs let you take advantage of the CNC produced grid of holes on the Festool MFT/3 multifunction table. The dogs are available in two sizes: 10mm high bench dog and 70mm high Parf dogs. By using a combination of bench dogs and Parf dogs to position your work and guide rail, you can easily achieve accurate repeatable cuts at 45° and 90°. Machined from stainless steel, each dog has a post that fits into the 20mm holes of the MFT/3 table top. Each size of dog is supported on the surface of the bench by a thicker boss or collar, 25mm in diameter and 10mm high, which provides a good bearing surface and stability in use. For additional security, each dog has a threaded hole to fasten it from below the table with an MFT3 accessory clamping knob (not included) or an inexpensive knob available separately.The two types of dog can be used for a variety of different purposes. Aside from its use as a low-profile stop, the small dog can be inverted and inserted from below the table top to exploit its M8 threaded through hole as an anchor point. The bench dogs can also be used to accurately set up the fence and guide rail on the MFT3 and the Parf dogs are great for making trammels for circular or arched router guidance. If you don't own a Festool table then a DIY cutting table can be produced using some 19mm MDF with a few 20mm holes bored at the required positions for 90° or 45° cuts.

13.97 16.76


Quantity:  






Veritas Small Surface Dog 20mm hole (Pair)  (Ref: 506451)

Veritas Small Surface Dog 20mm hole (Pair)

Key Features

Surface dogs for use with Festool MFT3 table
Quality product designed and manufactured by Veritas®
Threaded M8 for attaching jigs and accessories
Large or small sizes available



These surface dogs from Veritas® let you take advantage of the precise grid layout of the Festool MFT/3 table top for fast and repeatable work positioning, and are particularly useful for accurately aligning work in relation to the guide rail for 90° or 45° cuts. CNC machined from aluminium, they have a flat face for work registration and a rim that supports and stabilises them on the bench surface. Each dog has a post that fits into the 20mm holes of the Festool MFT/3 table top. They are supported on the surface of the bench by a thicker boss or collar, 25mm in diameter and 10mm high, which provides a good bearing surface and stability in use. For additional security, each dog has a threaded hole to fasten it from below the table with a suitable clamping knob available separately. The two sizes of dog can be used for a variety of different purposes. Apart from their use as a low-profile stop, the dogs can be inverted and inserted from below the table top to exploit the M8 threaded through hole as an anchor point. The bench dogs can also be used to accurately set up the fence and guide rail on the MFT3. If you don't own a Festool table then a DIY cutting table can be produced using some 19mm MDF with a few 20mm holes bored at the required positions for 90° or 45° cuts.

10.54 12.65


Quantity:  






Veritas Large Surface Dog 20mm hole (Pair)  (Ref: 506452)

Veritas Large Surface Dog 20mm hole (Pair)

Key Features

Surface dogs for use with Festool MFT3 table
Quality product designed and manufactured by Veritas®
Threaded M8 for attaching jigs and accessories
Large or small sizes available



These surface dogs from Veritas® let you take advantage of the precise grid layout of the Festool MFT/3 table top for fast and repeatable work positioning, and are particularly useful for accurately aligning work in relation to the guide rail for 90° or 45° cuts. CNC machined from aluminium, they have a flat face for work registration and a rim that supports and stabilises them on the bench surface. Each dog has a post that fits into the 20mm holes of the Festool MFT/3 table top. They are supported on the surface of the bench by a thicker boss or collar, 25mm in diameter and 10mm high, which provides a good bearing surface and stability in use. For additional security, each dog has a threaded hole to fasten it from below the table with a suitable clamping knob available separately. The two sizes of dog can be used for a variety of different purposes. Apart from their use as a low-profile stop, the dogs can be inverted and inserted from below the table top to exploit the M8 threaded through hole as an anchor point. The bench dogs can also be used to accurately set up the fence and guide rail on the MFT3. If you don't own a Festool table then a DIY cutting table can be produced using some 19mm MDF with a few 20mm holes bored at the required positions for 90° or 45° cuts.

12.21 14.65


Quantity:  






Veritas Muzzles for Bench Dogs (Pair) 32 mm  (Ref: 104275)

Veritas Muzzles for Bench Dogs (Pair) 32 mm

Key Features
Cushions bench dog's gripping surface
Non-marring, non-slip faces, firm grip without leaving marks
Muzzles slip easily over the head of bench dog
Length 32mm, supplied in pairs

Well named, these plastic muzzles take the bite out of Veritas Bench Dogs.

The ribbed faces provide non-marring, non-slip surfaces for clamping a finished piece without marking it. They have a firm, spring-grip, plastic body, which simply slips onto the head of the bench dog.

Length 32mm, supplied in pairs.

1.72 2.06


Quantity:  






Veritas Muzzles for Bench Dogs (Pair) 19 mm  (Ref: 104276)

Veritas Muzzles for Bench Dogs (Pair) 19 mm

Key Features
Cushions bench dog's gripping surface
Non-marring, non-slip faces, firm grip without leaving marks
Muzzles slip easily over the head of bench dog
Length 19mm, supplied in pairs

Well named, these plastic muzzles take the bite out of Veritas Bench Dogs.

The ribbed faces provide non-marring, non-slip surfaces for clamping a finished piece without marking it. They have a firm, spring-grip, plastic body, which simply slips onto the head of the bench dog.

Length 19mm, supplied in pairs.

1.47 1.76


Quantity:  






Veritas Woodworking >  Veritas Workbench Accessories



Veritas Workbench Accessories
Buy online at www.quality-woodworking-tools.com with FREE mainland UK delivery for all woodworking tools





Veritas Tools Homepage
Veritas Checkout
  View Basket
Veritas Tools UK Delivery
Free UK Delivery

Newsletter Subscription